ISSN 1008-5548

CN 37-1316/TU

最新出版

转弯管道内聚乙烯粉尘爆炸火焰传播规律

Flame propagation patterns of polyethylene dust explosion in elbow pipes


杨凯1, 王才隆1, 陈记合2, 时训先2

1.北京石油化工学院 安全工程学院, 北京 102617; 2.中国安全生产科学研究院, 北京 100012

引用格式:

杨凯, 王才隆, 陈记合, 等. 转弯管道内聚乙烯粉尘爆炸火焰传播规律[J]. 中国粉体技术, 2027, 33(4): 1-10.

Yang Kai, Wang Cailong, Chen Jihe, et al. Flame propagation patterns of polyethylene dust explosion in elbow pipes[J]. China Powder Science and Technology, 2027, 33(4): 1-10.

DOI:10.13732/j.issn.1008-5548.2027.04.011

收稿日期: 2026-06-10, 修回日期: 2026-08-22, 上线日期: 2026-11-17。

基金项目: 国家重点研发计划项目,编号:2023YFC3010605;应急管理部重点科技计划项目,编号:2025EMST100101;内蒙古自治区重点研发与成果转化计划项目,编号:2026YFSH0158。

第一作者: 杨凯(1986—),男,副教授,博士,硕士生导师,研究方向为爆炸安全理论与技术。E-mail:ycyangk@bipt.edu.cn。

通信作者: 时训先(1976—),男,教授级高工,博士,博士生导师,研究方向为工业安全与应急管理。E-mail: shixunxian@163.com。

摘要: 【目的】 揭示管道转弯结构对聚乙烯粉尘爆炸火焰传播行为的影响。【方法】 构建由内径为70 mm的竖直主管与水平支管组成的90°透明转弯管道实验系统,选取不同粒径等级的低密度聚乙烯(LDPE)、中密度聚乙烯(MDPE)和高密度聚乙烯(HDPE)粉尘,在统一的粉尘分散与电极点火条件下开展爆炸传播试验;采用2 500 fps高速摄像记录火焰前沿的时序位置,依据管壁标尺完成像素距离标定,并计算瞬时传播速度、峰值传播速度和平均传播速度,对比分析聚乙烯类型与粒径对火焰形态及传播动力学参数的影响。【结果】 火焰由点火区向竖直主管传播并在转弯点附近出现明显形态扰动,进入水平支管后亮度增强、前沿形态更加不规则;粒径对火焰传播具有显著影响,较小粒径粉尘点火后反应更迅速,火焰达到最大传播距离所需时间更短,瞬时传播速度峰值更高;90°转弯结构改变了火焰传播路径和局部流动状态,使转弯点附近形成速度突变和火焰前沿拉伸现象。【结论】 在本实验条件下,细粒径聚乙烯粉尘表现出更快的火焰传播和更强的局部速度波动,90°转弯区是火焰形态及传播速度发生突变的关键位置。

关键词: 转弯管道; 聚乙烯粉尘; 粉尘爆炸; 火焰传播; 瞬时传播速度

Abstract

Objective Polyethylene dust can accumulate in pneumatic conveying lines and dust collection ducts, where changes in pipe direction alter flame acceleration, local turbulence, and the transport of unburned particles. This study examines the combined effects of polyethylene density grade, particle size, and a 90° elbow on flame morphology, propagation distance, instantaneous propagation rate, and mean flame velocity.

Methods The experimental system consisted of a 0.65 m vertical quartz main pipe connected to a 0.50 m horizontal acrylic branch through a 90° elbow. Both pipe sections had an internal diameter of 70 mm. The ignition electrodes were installed 0.10 m above the pipe bottom, with a gap of 6 mm between the electrodes. The ignition delay, ignition energy, and dust dispersion pressure were maintained at 60 ms, 1 000 mJ, and 200 kPa, respectively. Low-density polyethylene (LDPE), medium-density polyethylene (MDPE), and high-density polyethylene (HDPE) dusts were dried at 50 ℃ for 12 h and classified into three particle size grades. The measured median particle diameters were 54.02, 119.0, and 285.8 μm for LDPE; 65.78, 128.6, and 281.2 μm for MDPE; and 51.12, 116.8, and 280.0 μm for HDPE. A Phantom VEO710L high-speed camera recorded flame development at 2 500 frames/s with a resolution of 1 280 × 800 pixels. An axial scale marked on the pipe wall was used to calibrate pixel distance. The outermost position with a marked brightness gradient was identified as the flame front, and its location after the elbow was expressed as the cumulative distance along the pipe centerline. The instantaneous propagation rate was calculated from flame-front displacement between successive frames, while the mean flame velocity was calculated from the ignition position to the maximum propagation distance.

Results and Discussion After ignition, a weak flame kernel formed around the electrodes and expanded laterally until it occupied the pipe cross-section. The flame then propagated upward through the vertical main pipe. For the LDPE sample with a median particle diameter of 54.02 μm, the flame filled the pipe cross-section laterally at approximately 70 ms, reached the upper end of the vertical section at 124.8 ms, and achieved its maximum cumulative propagation distance at 193.2 ms. Near the 90° elbow, the flame front underwent distinct changes in direction and shape. After entering the horizontal branch, the luminous region became brighter, and the flame front became more dispersed and irregular. Flow turning, wall interaction, pressure disturbance, and local recirculation in the elbow region modified the distribution of particles and gaseous products ahead of the flame. The resulting mixing increased the contact between combustible material and oxygen, while flame stretching and deformation produced fluctuations in propagation rate. Particle size significantly affected the spatiotemporal characteristics of flame propagation. Fine particles ignited rapidly after electrode discharge, reached their maximum propagation distance within a shorter period, and generally produced higher peak instantaneous propagation rates. Their larger specific surface area facilitated heating, thermal decomposition, and the release of combustible volatiles. Coarser particles showed a longer ignition and acceleration stage, smaller rate fluctuations, and a more gradual increase in propagation distance. The instantaneous propagation rate curves generally increased before or near the elbow and decreased during the later stage as combustible material was consumed and the flame weakened. Local deceleration or renewed acceleration occurred close to the elbow because the flow direction changed and the pressure wave interacted with the wall and the developing flame. The three polyethylene grades exhibited different trends in mean flame velocity. For LDPE and MDPE, the mean flame velocity decreased overall as particle size increased. For HDPE, the mean flame velocity increased from the finest grade to the intermediate grade and then decreased for the coarsest grade.This nonmonotonic response indicated that particle size interacted with material density,dust cloud dispersion uniformity, and local disturbance in the branch. Density grade and dispersion state also affected flame continuity and the location of velocity peaks. Fine particles occasionally generated discontinuous luminous zones in the late stage, whereas some larger particles formed a more continuous but slower flame region. Therefore, the elbow served as a transition zone in which flame propagation changed from concentrated upward movement to lateral expansion in the branch.

Conclusion Under the present experimental conditions,smaller polyethylene particles generally exhibit faster propagation and stronger fluctuations in instantaneous propagation velocity.The 90° elbow is the principal location of flame deformation,directional change, and local velocity variation. LDPE and MDPE show an overall reduction in mean flame velocity with increasing particle size, while HDPE shows an initial increase followed by a decrease. Particle size, polymer density grade, and elbow-induced flow disturbance jointly control flame propagation in the tested pipe system.

Keywords: elbow pipe; polyethylene dust; dust explosion; flame propagation; instantaneous propagation velocity

参考文献(References)

[1]陈刚, 张晓蕾, 徐帅, 等. 我国2005—2020年粉尘爆炸事故统计分析[J]. 中国安全科学学报, 2022, 32(8): 76-83.

Chen Gang, Zhang Xiaolei, Xu Shuai, et al. Statistical analysis of dust explosion accidents in China from 2005 to 2020[J]. China Safety Science Journal, 2022, 32(8): 76-83.

[2]王美琳. 聚乙烯粉尘爆炸危险性分析与工程设计防范[J]. 石油化工安全环保技术, 2026, 42(2): 49-53, 89.

Wang Meilin. Analysis of polyethylene dust explosion hazard and engineering design prevention[J]. Petrochemical Safety and Environmental Protection Technology, 2026, 42(2): 49-53, 89.

[3]Gan Bo, Gao Wei, Jiang Haipeng, et al. Flame propagation behaviors and temperature characteristics in polyethylene dust explosions[J]. Powder Technology, 2018, 328: 345-357.

[4]Pang Lei, Ma Ran, Hu Shoutao, et al. Flame propagation of local LDPE dust cloud in a semi-open duct[J]. Experimental Thermal and Fluid Science, 2019, 101: 209-216.

[5]Pang Lei, Cao Jiaojiao, Xiao Qiuping, et al. Explosion propagation in a dust removal pipeline under dust collector explosion[J]. Journal of Loss Prevention in the Process Industries, 2022, 74: 104662.

[6]Pang Lei, Cao Jiaojiao, Ma Ran, et al. Risk assessment method of polyethylene dust explosion based on explosion parameters[J]. Journal of Loss Prevention in the Process Industries, 2021, 69: 104397.

[7]郑秋雨, 刘琳, 刘天奇, 等. HDPE粉尘云/层最低着火温度研究[J]. 塑料工业, 2021, 49(4): 97-101, 106.

Zheng Qiuyu, Liu Lin, Liu Tianqi, et al. Study on minimum ignition temperature of HDPE dust cloud/layer[J]. China Plastics Industry, 2021, 49(4): 97-101, 106.

[8]吴雪梅, 朱顺兵, 吴佳梦, 等. 高密度聚乙烯粉尘燃爆特性及泄爆实验研究[J]. 中国安全生产科学技术, 2023, 19(10):144-150.

Wu Xuemei, Zhu Shunbing, Wu Jiameng, et al. Experimental study on combustion and explosion characteristics and explosion venting of high-density polyethylene dust[J]. Journal of Safety Science and Technology, 2023, 19(10): 144-150.

[9]Yu Xiaozhen, Chen Jihe, Meng Xiangbo, et al. Polyethylene deflagration characterization and kinetic mechanism analysis[J]. Energy, 2024, 303: 131990.

[10]Ding Jianfei, Qi Chang, Yan Xingqing, et al. Effect of airflow velocity on flame propagation and pressure of starch dust explosion in a pneumatic conveying environment[J]. Powder Technology, 2024, 433: 119147.

[11]Ding Jianfei,Yan Xingqing,Chen Lei,et al.Experimental study on the impact of airflow velocity and pipeline diameter on dust explosions in vessel-pipeline pneumatic conveying[J].Journal of Loss Prevention in the Process Industries,2024, 92: 105419.

[12]Ding Jianfei,Yan Xingqing, Jiang Yichang, et al.Effect of combination of explosion venting and chemical barrier on starch explosion suppression in a large scale connected vessels[J].Process Safety and Environmental Protection,2023,174: 734-744.

[13]Zhang Shulin, Bi Mingshu, Yang Mingrui, et al. Flame propagation characteristics and explosion behaviors of aluminum dust explosions in a horizontal pipeline[J]. Powder Technology, 2020, 359: 172-180.

[14]Li Chang, Ma Zepeng, Bu Yajie, et al. Experimental study on the minimum ignition energy of cornstarch particle-air flows in a horizontal pipeline[J]. Journal of Loss Prevention in the Process Industries, 2022, 79: 104842.

[15]Boeck L R, Bauwens C R L, Dorofeev S B. Large-scale dust explosions in vessel-pipe systems[J]. Journal of Loss Prevention in the Process Industries, 2023, 82: 104980.

[16]Han Bo, Li Gang, Yuan Chunmiao, et al. Flame propagation of corn starch in a modified Hartmann tube with branch structure[J]. Powder Technology, 2020, 360: 10-20.

[17]Jiang Chao, Pan Jianfeng, Zhu Yuejin, et al. Influence of concentration gradient on detonation re-initiation in a bifurcated channel[J]. Fuel, 2022, 307: 121895.

[18]Song Yifan,Zhang Qi.Multiple explosions induced by the deposited dust layer in enclosed pipeline[J].Journal of Hazardous Materials, 2019, 371: 423-432.

[19]李刚,胡朋,张洋洋,等.不同弯型管道内粉尘爆炸传播规律[J].东北大学学报(自然科学版),2020, 41(9):1316-1320.

Li Gang, Hu Peng, Zhang Yangyang, et al. Propagation laws of dust explosion in different types of elbow pipes[J]. Journal of Northeastern University (Natural Science), 2020, 41(9): 1316-1320.

[20]李刚,崔震,胡朋,等.双侧分支结构管道内粉尘爆炸传播规律[J].东北大学学报(自然科学版),2021,42(5):734-740.

Li Gang, Cui Zhen, Hu Peng, et al. Propagation laws of dust explosion in pipes with double-sided branch structure[J]. Journal of Northeastern University (Natural Science), 2021, 42(5): 734-740.

[21]Chen Xiangfeng, Gao Wei, Yang Mingrui, et al. Experimental investigation on PMMA dust explosion venting at elevated static activation pressure[J]. Powder Technology, 2021, 392: 402-411.

[22]Lin Song, Liu Zhentang, Qian Jifa, et al. Inertant effects and mechanism of Al (OH)3 powder on polyethylene dust explosions based on flame propagation behavior and thermal analysis[J]. Fire Safety Journal, 2021, 124: 103392.

[23]Zhang Yansong, Pan Zhichao, Yang Junjie, et al. Study on the suppression mechanism of (NH4)2CO3 and SiC for polyethylene deflagration based on flame propagation and experimental analysis[J]. Powder technology, 2022, 399: 117193.

[24]Yang Kai, Zheng Zhaorui, Chen Jihe, et al. Research on the suppression effect of wire mesh on low-density polyethylene dust explosion[J]. Fire Safety Journal, 2026,160: 104603.

[25]邓宁, 张明星, 王云端, 等. 脉冲喷吹聚乙烯滤料除尘器的清灰性能[J]. 中国粉体技术, 2022, 28(5): 40-47.

Deng Ning, Zhang Mingxing, Wang Yunduan, et al. Cleaning performance of pulse-jet polyethylene filter media dust collectors[J]. China Powder Science and Technology, 2022, 28(5): 40-47.